+86-18630226696

Contact Us

    China

    CHINA

    ADD: ChaoYangNan Str, 300m to BaoCang Express Way Exit, BaoDing, HeBei, China

    TEL: +86-312-2090169/2090165

    FAX: +86-312-2090165

    Email: sales02@metowd.com

    Iran

    IRAN

    ADD: No.3 - Golshid9 St. - Nakhlestan Blvd. - Shams abad industrial Zone -40km Tehran Qom Freeway - Tehran - Iran

    Postal Code: 1834175977

    Tel: 00982156231607-8

    Mob: 00989121350509

    Email: atiravesh@yahoo.com

    Anahita-GmbH

    Germany Design & Development Office

    Germany Design & Development Office

    ADD: Wellensiek 111, 33619 Bielefeld Deutschland, Germany

    Tel: 0049 521 9890 170

    Mob: 0049 163 5149 622

    Email: amir.malek@anahita-gmbh.de
    s.malek@anahita-gmbh.de

A series of factors for adjusting welding parameters in high frequency welding Fourth: welding speed

Jun 09, 2021

In the last issue, we learned the influence of welding power and frequency on the characteristics of high frequency welding process. In this issue, we learned the position and influence of high frequency welding speed on the welding process in product debugging.

 In high frequency welding, the influence of welding speed on welding process is mainly reflected in the following two aspects 

1. Influence of welding speed on heat affected zone

 

In the process of high frequency welding, what is the suitable welding speed. In fact, the optimal welding speed can be obtained by experiments under the condition of a certain welding frequency for the corresponding specification products, and taking into account the temperature requirements of air cooling and then entering the cooling tank for the welding seam cooling after extrusion. According to the requirements of weld width, surface and microstructure, the appropriate welding speed can be tested. When the welding speed is higher, the heat affected zone will be relatively narrow, because the heating time is short and the heat diffusion time is reduced, so the possibility of grain expansion in the heat affected zone is very small; The lower the welding speed is, the wider the heat affected zone will be. Because of the increase of heating time and heat diffusion time, the possibility of grain expansion of the material structure in the heat affected zone will increase. Therefore, if the power and unit conditions permit, the higher the high frequency welding speed is, the better the possibility of achieving high-quality product conditions will be. Therefore, the high frequency welding speed should not be too low, This is very important.

 

2. The influence of welding speed on the state of welding melt 

In high frequency welding, especially in the welding of stainless steel pipe, austenitic stainless steel pipe, duplex stainless steel pipe, aluminum pipe, copper pipe, titanium pipe and other non ordinary carbon steel materials, the influence of welding speed on the welding process will be very obvious, and sometimes even the key factor determining the success or failure of welding, so what kind of welding speed is OK? What is the reason?

 

In fact, when welding non ordinary carbon steel pipe, the welding speed parameter needs to consider the influence of welding speed on the composition and state of welding melt, mainly considering the oxide in the melt. Usually, the oxide of non ordinary carbon steel materials will have an adverse impact on the characteristics of the weld, and ultimately affect the quality of the weld. For example, the melting point temperature of the oxide produced in the welding process of stainless steel, aluminum, copper and titanium is higher than the fusion temperature of the base metal, so the oxide can not be dissolved and mixed in the weld, affecting the quality of the weld. In this case, the welding speed can not be too low, only to improve the welding speed, shorten the heating time, reduce the time of oxide formation, inhibit the generation of oxide, so as to reduce the oxide content and improve the welding quality.

 

The above two aspects need to be considered in the selection of appropriate welding speed. In general, the current final welding speed also needs to consider the main molding speed, flying shear speed, welding power supply speed limit and air cooling length of different materials and other factors. In the next issue, we will make a summary of the parameters that affect the welding process. Thank you for your attention!


Send Inquiry