+86-18630226696

Contact Us

    China

    CHINA

    ADD: ChaoYangNan Str, 300m to BaoCang Express Way Exit, BaoDing, HeBei, China

    TEL: +86-312-2090169/2090165

    FAX: +86-312-2090165

    Email: sales02@metowd.com

    Iran

    IRAN

    ADD: No.3 - Golshid9 St. - Nakhlestan Blvd. - Shams abad industrial Zone -40km Tehran Qom Freeway - Tehran - Iran

    Postal Code: 1834175977

    Tel: 00982156231607-8

    Mob: 00989121350509

    Email: atiravesh@yahoo.com

    Anahita-GmbH

    Germany Design & Development Office

    Germany Design & Development Office

    ADD: Wellensiek 111, 33619 Bielefeld Deutschland, Germany

    Tel: 0049 521 9890 170

    Mob: 0049 163 5149 622

    Email: amir.malek@anahita-gmbh.de
    s.malek@anahita-gmbh.de

Key factors of straightness control in quenching and heat treatment of bar and pipe

Apr 13, 2021

Key factors of straightness control in quenching and heat treatment of bar and pipe


In the process of quenching heat treatment in the continuous production on line, some products have clear requirements for the straightness control of bar and pipe. Generally, if the diameter of bar is less than 20mm, the larger the diameter of bar, the easier the straightness control is, and the smaller the diameter, the corresponding linear control needs to be paid attention to. Similarly, if the incoming material is a pipe, the straightness control should consider the wall thickness in addition to the diameter. Generally, the thickness of 2mm or less is considered. The corresponding linear control needs to be paid attention to, and the thicker the wall thickness, the straightness control is relatively easy. 

So, in the process of quenching heat treatment, whether it is bar or pipe continuous production on line, can the straightness of the product be controlled? We need to consider the following key elements and deal with them well: 


  1. Incoming material requirements 


Generally, the length of incoming materials is some sections, usually from 3m to 12M, and the linear property of long materials is generally required to be controlled within one thousandth. At the same time, it is required that there is no breakpoint between the incoming section and the section, especially the pipe, so as to prevent a large amount of quenching liquid from entering the pipe between the sections, which will affect the straightness of the products during the quenching process. If conditions exist, plug treatment shall be added at both ends of pipe when feeding.

 

2. Heating requirements of induction heating

 

At present, the on-line bar and pipe heat treatment heating is all conducted by rapid induction heating. During the induction heating process, the material will release the internal stress of the material. This requires that the heating must ensure the permeability of the heating to the material, and the surface temperature raising process cannot be too fast, especially for the bar, the temperature difference between the core surface and the core surface of the material must be reduced as much as possible. Generally, it is required to be less than 50 degrees, and the most important is to reduce the temperature difference between the core and the surface of the material To be less than 20 degrees.

 

3. Requirements for quenching and cooling

 

The control of the straightness of quenching cooling is very important. No matter bar or pipe, the metallographic structure is needed in the quenching process which meets the requirements of process materials, and there is no bending. It is usually necessary to ensure that the quenching medium system for cooling ensures that the quenchant has certain outlet pressure, flow, post outlet guide, continuity, 360 degree uniformity and stability outside the pipe rod. The secondary liquid (hot liquid) quenching produced by no hot liquid reflux is very important. And according to the size of the pipe rod, different nozzle forms, holes, nozzles or crevices are selected, which needs to be selected according to the product. In general, it is necessary to ensure that sufficient cooling is required under uniform conditions, so as to ensure straightness.

 

4. Speed requirements of production line

 

The speed of production line is a relatively tangled parameter. No matter what product, especially for QT equipment with on-line continuity, the process data of production speed cannot be infinite high, and the speed must match the induction heating and heating process and quenching and cooling process. These processes need to be calculated theoretically and combined with the actual product quality requirements. In short, it needs to be considered comprehensively.

 

In short, the above four points are considered in the process of controlling the straightness of products.



Send Inquiry