+86-18630226696

Contact Us

    China

    CHINA

    ADD: ChaoYangNan Str, 300m to BaoCang Express Way Exit, BaoDing, HeBei, China

    TEL: +86-312-2090169/2090165

    FAX: +86-312-2090165

    Email: sales02@metowd.com

    Iran

    IRAN

    ADD: No.3 - Golshid9 St. - Nakhlestan Blvd. - Shams abad industrial Zone -40km Tehran Qom Freeway - Tehran - Iran

    Postal Code: 1834175977

    Tel: 00982156231607-8

    Mob: 00989121350509

    Email: atiravesh@yahoo.com

    Anahita-GmbH

    Germany Design & Development Office

    Germany Design & Development Office

    ADD: Wellensiek 111, 33619 Bielefeld Deutschland, Germany

    Tel: 0049 521 9890 170

    Mob: 0049 163 5149 622

    Email: amir.malek@anahita-gmbh.de
    s.malek@anahita-gmbh.de

Key elements of straightness control in quenching and heat treatment of bar and pipe

Aug 28, 2021

In the actual quenching heat treatment production process of on-line continuous production, some products have clear requirements for the linearity control of bars and tubes. Generally, if the diameter of the bar is less than 20mm, the larger the diameter is, the easier the linearity control is, and the smaller the diameter is, the corresponding linearity control needs to be paid attention to. Similarly, if the incoming material is pipe, besides the diameter, the wall thickness also needs to be considered for linearity control. Generally, the wall thickness of 2mm and below needs to be paid attention to. The thicker the wall thickness, the easier the linearity control is.


So whether it is the quenching heat treatment production process of on-line continuous production of bar or pipe, can the linearity of the product be controlled? We need to consider and deal with the following key elements:


1. Incoming material requirements


Generally, the length of incoming materials is some segmental materials, usually ranging from 3m to 12m. Generally, the linearity of long materials is required to be controlled within one thousandth. At the same time, it is required that there is no breakpoint between the incoming material sections, especially the pipe, to prevent a large amount of quenching liquid between the sections from entering the pipe, which will eventually affect the straightness of the product in the quenching process. If conditions permit, plugs shall be added at both ends of the pipe during incoming materials.


2. Temperature rise requirements of induction heating


At present, rapid induction heating is used for the heat treatment and heating of on-line bars and pipes. In the process of induction heating, the material will release the internal stress of the material, which requires that the heating must ensure the permeability of the heating to the material, and the surface temperature rise process cannot be too fast. Especially for bars, it is necessary to try to reduce the core surface temperature difference of the material, which is generally less than 50 degrees, It is best to be less than 20 degrees.


3. Requirements for quenching cooling


Quenching cooling is a very important link for the control of straightness. Both bars and pipes need to continuously obtain the required metallographic structure in the quenching process meeting the requirements of process materials without bending. It is usually necessary to ensure the quenching medium system for cooling, ensure that the quenching liquid has certain outlet pressure, flow, post outlet guidance, continuity, 360 degree uniformity and stability outside the tube and rod, and there is no second-hand liquid (hydrothermal) quenching caused by hydrothermal reflux. These elements are very important. Different nozzle forms, such as hole, nozzle or gap, shall be selected according to the size of the pipe rod, which shall be selected according to the product. Overall, it must be ensured that sufficient cooling is required under uniform conditions, so as to ensure straightness.


4. Production line speed requirements


The speed of the production line is a tangled parameter. No matter what product, especially for QT equipment with on-line continuity, the process data of its production speed can not be infinitely high. The speed must match the induction heating process and quenching cooling process. These treatments need to be combined with the actual product quality requirements in addition to theoretical calculation. In short, it needs comprehensive consideration


Send Inquiry