Contact Us
CHINA
ADD: ChaoYangNan Str, 300m to BaoCang Express Way Exit, BaoDing, HeBei, China
TEL: +86-312-2090169/2090165
FAX: +86-312-2090165
Email: sales02@metowd.com
IRAN
ADD: No.3 - Golshid9 St. - Nakhlestan Blvd. - Shams abad industrial Zone -40km Tehran Qom Freeway - Tehran - Iran
Postal Code: 1834175977
Tel: 00982156231607-8
Mob: 00989121350509
Email: atiravesh@yahoo.com
Germany Design & Development Office
Germany Design & Development Office
ADD: Wellensiek 111, 33619 Bielefeld Deutschland, Germany
Tel: 0049 521 9890 170
Mob: 0049 163 5149 622

Seam Annealer
E quipment Introduction It is the special equipment successfully developed by our company based on the full absorption of the advanced foreign equipment experience in China in recent years, which is used by the pipe industry to produce high-grade steel pipes. The high-frequency welding equipment...
Description

Equipment Introduction
Seam Annealer is the special equipment successfully developed by our company based on the full absorption of the advanced foreign equipment experience in China in recent years, which is used by the pipe industry to produce high-grade steel pipes.
The high-frequency welding equipment and the online annealing dedicated IF heating equipment for steel pipes are centralized in the rear of the unit, which follow the sequence of unwinding → loop → forming → welding → planer tool → weld annealing → air cooling section → 300 ℃ cooling → sizing → cutting → blanking raceway → packing order.
Points: the air cooling section should be reserved according to the speed and the annealing temperature.
The entire equipment is divided into two parts: electrical parts and mechanical parts.

Seam Annealer Adjust the frequency as needed so that the temperature rise curve makes the welding seam even and diathermal. For equipment of different diameters and wall thicknesses, users can choose to open the number of IF equipment, which can not only achieve the purpose of annealing but also save the energy.
Seam Annealer Electrical parts
Rectifier circuit
Introduction of electric circuit theory principles
Actually, the thyristor IF power supply is an AC-DC-AC converter. Its basic principle is as shown in Figure 1

Figure 1 AC - DC - AC converter block diagram
The three-phase power frequency current is rectified into pulsating direct current, then it becomes the smooth direct current through the filter. After that, it is converted to an IF current supply load (induction coil) within a certain frequency range by the inverter to heat the metal workpiece.
The three-phase bridge full-controlled rectifier is as shown in Figure 4. Two of the six thyristors are conducted at the same time for each moment during the rectification process, which means that the loop can be formed when one thyristor in the common cathode group and the other thyristor in the common anode group are conducted at the same time.
Control elements
Low-voltage electrical appliances mainly use products of domestic brands.
Inlet filter
The inlet should be equipped with the filter circuit and the inlet reactor, which can effectively control the pollution on the power grid.

Conditions of use environment
a) It is installed inside. The grounding is good. The grounding resistance is not greater than 4Ω.
b) The ambient temperature is not higher than 40 ℃ and not lower than -15 ℃.
c) The air relative humidity is ≤ 85%
d) There is no conductive and explosive dust on the site. There are also no caustic metals, insulating gases and vapors.
e) No violent vibration and shock.
f) The temperature of the equipment cooling water outlet shall not exceed 60 ℃.
g) If there is frozen phenomenon when the temperature is lower than 0 ° C, if the product is stopped for a long period of time, the accumulated water in the components should be blown out to prevent the components from cracking.
h) The pressure of the cooling water inlet is 0.15-0.3MpaGrid requirements
a) The grid input voltage: three-phase 380V.
b) The grid voltage continuous fluctuation range: ± 10%.
c) The three-phase voltage balance is less than ± 5%.
Custom Notebook Solutions

Adjustable mechanical lifting device (mobile trolley)
Seam Annealer is mainly used to adjust the gap and distance between the IF sensor and the pipe weld.
The sensor lift and drop functions are pneumatic.
Both ends of the sensor are equipped with stainless steel adjustable support guide wheels, which have the support and anti-collision effect.
The button control with rocker facilitates the close operation.
It is mainly used for the sensor to right the welding seams.
It is equipped with electric rise and drop function, easy to adjust the gap between the sensor and the steel pipe.
It is equipped with electric forward and back function, easy to adjust the sensor to right the welding seams.
Both ends of the sensor are equipped with adjustable stainless steel guide wheels.
The output cabinet and mobile trolley are combined together. The mechanical and electrical integration can adapt to the seam annealing of various straight steel pipes.
It has the arc-type electric tracking function so that when the seam deviates from the center, users can track the angle of ± 7 °.
The sensor and steel pipe welding seam have the straight line angle adjustment.
Clamping deviceFunction: The IF heating sensor generates a strong magnetic field during operation, and the steel pipe will also bend and deform when heated.Will collide with the sensor and ignite.So small diameter steel pipes require clamping and fixing devices during heating.Prevent deformation and sparking..


choose us
Contact: Lulu sales02@metowd.com
WhatsApp: +86-18630226696
one-stop solution
professional team
high quality
Hot Tags: seam annealer, China, manufacturers, suppliers, factory, customized, wholesale, buy, made in China, Stainless Steel Pipe Off Line Annealing, Middle Frequency Online Annealing Equipment, On Line Annealing Equipment, Annealing Equipment, online MF mf annealing equipment, The High Hydrogen Bell Annealing Furnace
You Might Also Like











