Contact Us
CHINA
ADD: ChaoYangNan Str, 300m to BaoCang Express Way Exit, BaoDing, HeBei, China
TEL: +86-312-2090169/2090165
FAX: +86-312-2090165
Email: sales02@metowd.com
IRAN
ADD: No.3 - Golshid9 St. - Nakhlestan Blvd. - Shams abad industrial Zone -40km Tehran Qom Freeway - Tehran - Iran
Postal Code: 1834175977
Tel: 00982156231607-8
Mob: 00989121350509
Email: atiravesh@yahoo.com
Germany Design & Development Office
Germany Design & Development Office
ADD: Wellensiek 111, 33619 Bielefeld Deutschland, Germany
Tel: 0049 521 9890 170
Mob: 0049 163 5149 622
Elecgtrical Metallizing Machine
The spraying speed of QDIII - 250 High-speed Electric Arc Spraying Gun particles can reach above 300 m/s. The airflow speed of the spray nozzle can reach about 420 m/s. The coating density is more than double of the ordinary electric spray gun. Porosity < 3%. Spray particle deposition rate...
Description
The spraying speed of QDIII - 250 High-speed Electric Arc Spraying Gun particles can reach above 300 m/s. The airflow speed of the spray nozzle can reach about 420 m/s. The coating density is more than double of the ordinary electric spray gun. Porosity < 3%. Spray particle deposition rate > 75%. The adhesive strength of the coating and the pipe surface is high. At the same time, the power supply and control are designed as one whole part, making the equipment more compact. Especially the spray gun adopts remote control air and electrical switches, making operation more convenient, solving the problem that there must be two workers operating at the same time, and realizing the long distance spraying and spraying at heights or spraying inside container. Adopting the safe pressure makes the operation safe and reliable.
This machine is mainly used for large area and long-term anti-corrosion of bridges, sluice gates, ships, oil and gas pipelines, iron towers, lamp-posts and other steel structure, and spraying repairment of paper dryer, printing roller, crankshaft and other workpiece. It can also be applied to the capacitor, electric porcelain spraying, etc. The gun adopts stepless speed regulation. It can spray metal wire of different melting point such as zinc, aluminum, zinc alloy, copper, terne metal, high carbon steel, and stainless steel. Spraying wire specification is from Ø 1.2 to 3.0 mm.
(1) Start the air compressor, keeping the air pressure above 0.6 MPa.
(2) Keep the switch on the left side of the spraying machine to the "wire feeding" position, switch on the right side to the "internal control" position. Switch on the "main power", the power indicator will light up, the cooling fans begin to work. Keep "gun switch" to "on" position, set the gun voltage. The wire feeding speed is proportional to the spray gun voltage. You can get gun voltage by adjusting "wire feeding adjustment", gun voltage meter will display its value. Then close the gun switch.
(3) Wire wearing, make the two wires respectively through the hosepipe, rear conduit pipe, then former conduit pipe, until to the air cap mouth . Press "tight" knob to adjust the pressure (till you cannot pull the wires). Inch "switch" on the gun and adjust coordinate with the "tight" knob. Cut the wire outside the air cap flat and separate them after adjusting the wire feeding.
(4) Choose working voltage. Keep the switch on the left side of the sprayer to "spray" position. There will be air out of the gun at this moment. Adjust "coarse tuning" and "fine tuning" to set the required voltage, the voltage value will be displayed through the work voltage meter.
(5) Spraying, first open "gas electrical switch” on the gun, then click the "gun switch" to check if the voltmeter and ammeter suitable to spraying requirements, and check the spraying effect. Ideal spraying beam angle can be achieved by adjusting the distance between air cap and the wire intersection.
(6) Spray finished, close “spraying switch" first, then close "gas electrical switch", at last close "main power switch".
(7) Start-stop mode one: when switch on the right side of the sprayer in the position of "internal control", open the switch of the gun, control the start-stop of the gun by the switch on the left side of the sprayer.
Stop-start mode two: when switch on the right side of the sprayer in the position of "internal control", keep the switch on the left side to the "spraying" position, control the start-stop by the gun switch.
Stop-start mode three: when switch on the right side of the sprayer in the position of "external control", keep the switch on the left side to the "spraying" position, control the start-stop by heating relay on the console.
Maintains Requests
1.This sprayer should be placed in ventilated and dry place, and pay attention to dustproof, waterproof and suncare. Ambient temperature is suitable for - 10 ℃ to 40 ℃. Elevation should be less than 1000m.
2. Daily maintenance: check and clear metal dust on the sprayer everyday, shave metal spatter on air cap and arc hood, replace the worn parts and take care of.
3. Weekly maintenance: clear metal dust inside the arc spraying machine with brush or compressed air < 0.2 MPa every week. Check and fasten electric pile connection, especially the ground wire must be safe and firm; the worker should replace the wire with high temperature melting or aged in time.
4. Monthly maintenance: inspect and clean each of the transmission parts, gear box of the gun; replace lubricating oil and worn parts or transmission parts.
Contact Us
Hot Tags: elecgtrical metallizing machine, China, manufacturers, suppliers, factory, customized, wholesale, buy, made in China, Spraying machine for large place, Zinc Coating Machine, Zinc Arc Spraying Machine, Electrical Spraying Machine, Arc Spraying Machine, Electrical Zinc Spraying Machine
You Might Also Like














